Basic Outdoor Knife

by Common Man Survival in Workshop > Metalworking

9652 Views, 119 Favorites, 0 Comments

Basic Outdoor Knife

54e5f72ed535cf97b500015d.jpeg
54e5f85adbf3ec430d000006.jpeg

I've always wanted to make a knife for myself and this is Instructable will be that journey. I will be talking about materials, sourcing materials, minimal tools necessary, designing the knife, heat treating, and attaching handle slabs.

I have to stress the fact that I am no expert on the topic of knife making and the processes involved in it. This is what I did, right or wrong, I hope you enjoy and learn a lot.

Know Your Materials and Sourcing

54e5ecccec8d83bc4f000127.jpeg
54e5ecaaec8d83055d00000f.jpeg

At your local hardware store, you'll find flat steel stock in various thicknesses, widths, and lengths. I thought it was awesome, an 8 foot x 2 inch x 1/8 thick piece of steel was only $14. I could cut several blanks from it and be completely content with the money spent but the quality of the steel is far too poor to hold an edge.

Researching what types of steels would be good for a beginner like myself, I found that 1084 and 1095 high carbon steel would be good. There is also 01 tool steel and stainless steels such as 440C but they are little bit more expensive so for a first knife, I'm avoiding it. Unfortunately, knife steel is much more expensive than structural steel. I found that living in Canada, knife steel is very difficult to come by.

I will be ordering my steel from Canadian Knifemaker Supply Ltd (https://www.knifemaker.ca/home.php)

Steel is sold by the inch and is much more expensive compared to the hardware store steel but the work and time put into a blade will be wasted if you start with poor quality materials.

Designing Your Knife

54e5ed0cec8d83055d000010.jpeg
54e5ec6b2f7cc6bdb80001db.jpeg

Your knife is only limited to your imagination (and the dimensions of the steel you're working with). I recommend drawing the stock to scale on a piece of graph paper and sketching your knife design on it. Try to minimize the wasted material.

I wanted a very basic knife on the small side.

Transfer it to your knife blank with a photocopy and some glue.

Rough Cut

54e5ed6dd535cfb71e00020e.jpeg
54e5ef83f92ea19780000032.jpeg
54e5f10f2f7cc64e3100005d.jpeg
54e5efe5d535cffb7e00004a.jpeg
54e5f0762f7cc620ab00009d.jpeg
54e5f08b182470e41f000002.jpeg

Cut out your blank with a metal cutting hacksaw, bandsaw, etc. Drill pin holes. Make sure to keep it cool using a bucket of water.

Mark your bevel's center line making sure to leave it on the thicker side to prevent warping during heat treatment. I marked the point to file out by marking the edge with a marker then dragging a caliper on either side. The same thing can be done with a drill bit on a flat table. Clamp to the edge of a table and file out the bevel.

Drill holes for brass pins in handle.

Heat Treat

PHOTO_20150218_101247.jpg
54e5f18b2f7cc65ba200004f.jpeg
54e5f1a8dbf3ec3f920000e7.jpeg
PHOTO_20150218_110708.jpg
PHOTO_20150218_110711.jpg
54e5f215dbf3ec4b7b0001cf.jpeg
54e5f233dbf3eca52f0000c6.jpeg
54e5f24dec8d83055d000018.jpeg
54e5f26adbf3eceba5000018.jpeg

You're going to need heat up the blade to critical temperature. Looks pale red and no longer is magnetic.

Easier said than done when on a budget.

After an epic fail which resulted in my makeshift forge melting, I strolled the aisles of my local dollar store and found a stainless steel utensil holder similar to the ones some people buy from Ikea and make into outdoor stoves. New forge found.

I also did not have charcoal and (for some reason) happened to have hardwood pellets on hand. After using them, I suggest using charcoal. Using wood pellets resulted in much more flame and much less coal in the end, unfortunately.

After critical temperature is reached, dip in an oil to quench and harden the blade.

Clean it off and place in a toaster oven at 450 degrees for an hour to temper.

Sharpen

54e5f2821824708493000001.jpeg

Sharpen your blade with your preferred method of sharpening blades. Cover blade for next step to prevent cutting yourself.

Handle

54e5edfe9d29c916f5000105.jpeg
54e5ee31dbf3ec4b7b0001cc.jpeg
54e5ee61dbf3ec1a92000007.jpeg
54e5eea1ec8d83408b00002d.jpeg
54e5eec1dbf3ec1a92000008.jpeg

Glue handles and pins using 5 minute epoxy and clamp until glue is set. For handles, I just used slabs of wood I cut from firewood.

File shape of the handle using a round file then sand smooth.

Treat handle with your oil or stain of your choice.

Debrief

PHOTO_20150219_094245.jpg

Total Cost: about $10.00

  • 3/34" 1095 steel ($4.00)
  • Brass pin 12" ($1.50)
  • Utensil holder ($3.00)
  • 5 Minute Epoxy ($1.50)
  • Wood slabs (Free)

This project was fun and a great learning experience for me. I highly recommend you try it yourself, especially if you use a knife in your favourite past times (cooking, camping, bushcraft, etc).

Things that would make this project not a pain in the butt:

  • Drill press
  • Belt sander
  • Angle grinder
  • Propane fueled forge
  • Quality wood slabs

Total time without all these things that would have made everything so much easier: 8 hours.