Castle Planter (with Tinkercad Code Blocks)

by Josiah Miller in Circuits > Websites

2767 Views, 14 Favorites, 0 Comments

Castle Planter (with Tinkercad Code Blocks)

Planter finished 2.png

This design here took me quite a while to accomplish, and since my coding skills are, limited to say the least, I hope it turned out ok :) Using the instructions provided you should be able to completely recreate every aspect of this design without any outside help, skill, or knowledge. Every picture has the code on the side and when combined it will create the entire project!

you will probably need to click on the pictures to get the whole view. sorry.

Make sure on every step to look at the code in the picture it will get you a long way!

Hope you like it! :)

here it is in Tinkercad https://www.tinkercad.com/codeblocks/2VzJT7vCa4Q-the-statue-of-liberty-base-planter

Supplies

Computer, and time thats about all you need.

Step 1: the Base

step 1.png

pretty self explanatory

Step 2: Cube With a Hole

step 2.png

just do the written code.

Step 3; Again

step 3.png

This is step two over again, eventually we will miter the bottom one to the top with a pyramid.

Step 4: First Bricks

step 4.png

the bricks are all in a row just do what the code shows. :)

Step 5: First Circles

step 5.png

These are the first circles, just like the bricks they are in a row and you can copy the code.

Step 6: Bricks

step 6.png

need I tell you to follow the code :) its the same thing but rotated 90 degrees.

Step 7: Second Set of Circles

step 7.png

just like the first one, but rotated 90 degrees

Step 8: What Do You Know! Its Bricks Again!

step 8.png

Its bricks again same old thing as the other two just do this one twice, and rate 180 degrees. Or follow the code :)

Step 9: Bricks

step 10.png

This time you need to raise the bricks just above the first set. there are two sets here, and they need to be offset as the picture and code shows.

Step 10; Bricks Row 2 Finish

step 9.png

finish off row two!

Step 11: Bricks

step 12.png

well better get started on row three! noticing a theme.

Step 12: Bricks Finish

step 11.png

Finally we get to finish the bricks! :) hurray. If you didn't lear from the last 100 times, all you have to do is follow the code :) lol

Step 13: Miter It Off!

step 13.png

use the pyramid and cut the top. also get those edges aligned!

Step 14: Circles Number 3!

step 14.png

well here we go again, same concept as the bricks same concept as the other two circles. ENJOY!

Step 15: Circles Again!

step 15.png

Its the end of the circles you have been rotating them like crazy! :)

Step 16: New Miter

step 16.png

follow the same concept as the last one, look at the code! :)

Step 17: the First of the Pyramids

step 17.png

seeing a trend here! :)

Step 18: the Second of the Four Pyramids.

step 18.png

enjoy doing it again rotate 90 degrees!

Step 19: Pyramids

step 19.png

try for three!

Step 20: Pyramid Finish

step 20.png

Just follow the code in the picture and you will be fine!

Step 21: Tower

step 21.png

there appears to be a lot going on here, but there are actually few shapes stick to the code and you will be fine.

Step 22: Support

step 22.png

again stick to the code! most of this is just for decoration. :)

Step 13: Top and Windows

step 23.png

black the windows, and miter the top, makes it printable! :)

Step 24: Crenelations

step 24.png

its just holes in the top! :) look at the code to decide what to do.

Step 25: Decor

step 25.png

you are finally finished! great job! hope you loved this inscrutable. yes it should be 3D printable.