How to Turn a Dip Pen

by Wanjun in Workshop > Woodworking

25894 Views, 145 Favorites, 0 Comments

How to Turn a Dip Pen

9J2B3310.jpg

I recently started practicing pointed nib calligraphy so I decided to make some myself. It was surprisingly easy! You don't need a pen kit or any bushings. The finished dip pen is beautiful and most importantly balanced.

This project is very inexpensive if you have access to a wood lathe. The lathe parts required are standard with the exception of the 7mm drill bit. The trick is turning a jam chuck yourself so you don't have to buy a fancy closed-end pen mandrel and its specialty chuck.

Tools and Supplies

55b19c7f4936d40ee50006f3.jpeg
9J2B3254.jpg
9J2B3304.jpg
9J2B3315.jpg
55b1a26945bcebd25c000732.jpeg

Tools:

  • Wood lathe with the following parts and big enough to turn 12 inch stock
    • chuck with jaws that can compress down to about 1/2 inch diameter
    • live center
    • drive center
    • drill chuck
    • 7mm drillbit
  • Tube Cutter
  • Calliper
  • (not pictured) Turning tools. I like carbide for rough shaping and HSS for final shaping and detailing.
  • PPE - safety goggles and respirator

Supplies:

  • Turning Stock - I used black and white ebony 3/4 inch by 3/4 inch by 12 inch that I ripped from a larger square stock. I recommend tight-grained dense hardwoods such as lignum vitae, desert ironwood, tulipwood, etc. I made my first one out of cherry and it was too light.
  • Sandpaper - varying grit from 150 to 600
  • Finish - I used a walnut oil and beeswax finish. Use anything you like.
  • Masking tape
  • 7mm brass tube - I bought a 10 pack for all of $2.50 from pennstate where you can also pick up the 7mm drill bit. if you don't want to pay for shipping you can get them at your local Rockler or Woodcraft.
  • CA Glue - or super glue
  • Pen Insert - holds the nib in regular nib holders. I haven't been able to find them anywhere but JohnNealBooksellers which is also where I buy all my calligraphy supplies.
  • Sugru - optional.

Turn a Tenon

55b1a823937ddbb25e000759.jpeg
9J2B3262.jpg
  1. Decide on the orientation. Tail end should go on the tail stock.
  2. Turn a tenon on the tailstock side.

Cut Brass Tube to Size

9J2B3257.jpg
9J2B3260.jpg

It should be able to house the pen insert. See photo for precise measurements.

Drill a Hole to Length

9J2B3264.jpg
9J2B3265.jpg
  1. Take your live and drive centers off and chuck up your tenon with the 4-jaw chuck.
  2. install drill chuck with pen drill on the tail end
  3. use masking tape to mark on the drill correct depth.
  4. drill into the wood until you hit the masking tape.

Glue in the Brass Tube

9J2B3266.jpg
9J2B3272.jpg

Before you apply CA glue test fit it to make sure the hole is deep enough.

Square Off the End

9J2B3274.jpg

Wait for the glue to dry and carefully square off the end to free it of leftover CA and to make flush brass tube and wood.

Turn Holder to Size

9J2B3276.jpg
9J2B3277.jpg
9J2B3280.jpg
9J2B3282.jpg
  1. Put the live center back on the tail stock.
  2. Rough down your stock.
  3. With your calliper measure the insert and turn down the nib end to for a seamless joint.

Rough Shape Then Fine Shape

9J2B3284.jpg
9J2B3286.jpg
9J2B3288.jpg

Customize and shape the pen. I held it intermittently with my writing hand to make sure it felt right.

Remember to always turn downhill.

Finalize the thicker diameter shape before tapering off the thin end.

At this point I noticed a wormhole right in the middle grrrr! I just left it alone.

Finish the Body

9J2B3290.jpg
9J2B3291.jpg

I sanded to 600 grit and rubbed in my walnut oil and beeswax finish with a shop towel.

Part Off the Pen

9J2B3293.jpg
9J2B3295.jpg

Loosen your tail stock a bit. This is to relieve pressure off the spindle, allowing for a very fine part.

I parted this by tapering down, with light cuts and a sharp tool.

Turn a Jam Chuck

9J2B3296.jpg
9J2B3297.jpg
9J2B3298.jpg

The tip from when we parted off is unfinished so this is all for finishing the tip.

Use the calliper to measure the inside diameter of the brass tube and turn a recess down to just a hair smaller.

Wrap the masking tape around a couple of times, tear off excess and jam the pen onto the jam chuck. `

Finish the Tip

9J2B3300.jpg
9J2B3299.jpg

Sand down and finish the tip as you did the body. The makeshift jam chuck does not spin true and will only become more and more wobbly so support it with your fingers, and always sand from right to left.

Assemble and Enjoy!

9J2B3301.jpg
9J2B3313.jpg
9J2B3305.jpg
9J2B3309.jpg

Hand press the pen insert in your holder and put a nib in it! It's a joy to use and makes me look forward to practicing calligraphy.

If you don't mind permanently marrying a nib to a holder, use Sugru instead of a pen insert. Sugru has the added benefit of waterproofing the nib holder.

I also added in a small ball bearing to weigh down very first one I made out of cherry.