DIY Alarm With Phone
Ever wanted to know how to make your own alarm system? Believe it or not, you can make your own alarm for about $10 with a few simple hacks to a prepaid cellphone. You can easily catch intruders who set off the tripwire, because this neat little gadget calls your cellphone right when it happens.
This instructable shows you how to make such a device, and all it’s going to take are a few common tools, a couple of hours and a $10 Tracfone from Target.
Like this project? Check out my other instructables, my favorite survival stuff, my cool DIY Projects and my paracord tutorials.
How to Make a DIY Alarm/Tripwire
Follow these simple steps and you will soon have an awesome little gadget that alerts you to any unwanted intruders. You will immediately get a call on your phone alerting you that your tripwire has been activated.
Supplies and Tools You Will Need:
- 1 Pre-paid phone (We used a $10 Tracfone)
- 1 Soldering Iron (You can get a cheap one at Radio Shack)
- 60/40 Rosin-Core Solder
- Some wire
- 1 Box cutter
- 1 Small phillips head screwdriver
- 1 Hot glue gun with glue
- Tin Foil
- 1 Clothespin
Begin by following the instructions in the phone’s manual to activate the phone. We went online to activate ours, but if you don’t have an internet connection there’s a number you can call as well. All of this information can be found in the box that the phone came in.
Next, we need to program the phone’s speed dial function to call your phone number when the number 8 key is held down.
First, Enter your phone number into the phone by going to: Menu >> Contacts >> Add New Contact
Once you’ve added yourself to the phone’s contact list, pair your number with the phone’s number 8 key by going to: Menu >> Contacts >> Speed Dial List
Select cell number 8, and then select your name from the contacts list.
If you’ve done this correctly, it will look like this.
Remove the screws from the back plate and disassemble the phone. There are five screws total.
The arrows show you where you will find the screws you need to remove.
Use a small Phillips head screw driver to remove the screws.
Remove the screws one by one.
Once the screws are out, you can use your box cutter to pry the back plate from the front plate. It takes a bit of force and will make a loud snapping sound as it separates, so don’t worry about breaking it because you wont. Once you’ve created some space with the box cutter, you can use your fingers to do the rest of the work.
Using a utility knife, gently pry the edges of the cell phone apart. When you’ve pried it apart, it will be in three pieces.
The phone will come apart and you will have three pieces, front plate, middle, and back.
Locate the button on the middle piece that corresponds with the number “8″ on the front plate of the phone, where the numbers are. This will expose a copper ring with a copper circle in the middle of it. We need to solder a wire to each of them without crossing them.
IMPORTANT NOTE: YOU NEED TO KNOW SOLDERING BASICS
If you screw the next step up, then the phone will be ruined and you’ll have to buy another.
Don’t worry, it’s not that hard. But you’ll probably want to practice on a circuit board before proceeding.
TIP: You can buy circuit boards like this from Radio Shack for $5. They also sell wire, solder and soldering irons.
Once you can solder wires this close without having the solder touch, you’re ready to move on to the real deal.
With a soldering iron, place a small amount of solder on the tip of a wire.
Don’t go overboard. This much will do.
Now solder the wire to the copper circle in the middle of the copper ring. The solder can not touch the gold ring around it or the button will be ruined. This is why you practiced first 
Repeat the same steps with another wire, this time soldering it to the outer ring. Again, make sure the ring stays separated from the circle.
Test your soldering by touching the two wires together. The phone should work normally as if you were pressing the number 8 key on the keypad. If you screwed it up, nothing will happen.
Use the box cutter to cut the number 8 from the keypad.
Thread the two wires through the keypad and then reassemble the phone.
Once the phone is assembled, drip glue from a hot glue gun into the hole to keep the wires secure.
Now, take a strip of aluminum foil and fold it over the end of one of the wires.
Using your fingers, bend the end of the wire back onto itself.
Wrap the aluminum foil around the wire to secure the fitting.
Use a clothespin to clamp the end of the wire as shown.
Fold the aluminum foil over the top of the clothespin and secure it into place with the hot glue gun.
Secure the wire onto the body of the clothespin with hot glue.
Repeat these steps with the other wire and fasten it to the other half of the clothespin.
Braid the two wires together by twirling the clothespin.
Fasten the clothespin to the back of the phone with hot glue.
And your tripwire is complete!
How to set up and activate your tripwire :
The clothespin holds the number 8 key down on the phone, and so you need to separate the two halves with a thin piece of paper. Receipts work great for this.
When the paper is removed, the contacts on the clothespin touch and the phone will speed dial your number.
You’re probably going to need to exit out of the door that you’re booby trapping—I mean trip wiring—and so you’ll need to set it up like this:
Tape your trip wire device to the wall and drape the string over the doorknob.
Run the string under the door and make sure to give yourself enough slack to get outside.
Once you’re outside, it will look like this.
Slowly close the door while pulling the string under the door toward you. Don’t pull it tight, but remove all the slack until you feel it tugging against the doorknob on the other side.
Just before you shut the door, tape the string to the threshold.
Now cut it and shut the door.
You won’t be able to see it because you’ll be outside, but this is what your beautiful craftsmanship will look like from the inside.
