Drill Press Table

by shopbuilt in Workshop > Woodworking

45760 Views, 460 Favorites, 0 Comments

Drill Press Table

A basic drill press table
table1 (1 of 1).jpg

Nine times out of ten, you don’t need a drill press table but it sure would be nice for that one time. Because it’s use is so limited I wanted to keep the design/build simple, no frills. Also mounting needed to be quick and easy.

Table Material:

Screen Shot 2017-01-22 at 8.12.00 PM.png

The table itself well be two pieces of ¾” plywood laminated together. I just so happen to have some scrap plywood already doubled up in the shop from a pervious project so it was just a matter of cutting out a 15” by 18” rectangle on the table saw. The size is really just personal taste, I just wanted something as small as I could get away with to make it easy to store away.

Table Mounting

Screen Shot 2017-01-22 at 8.12.23 PM.png

To mount the homemade table to the drill press table as easy as possible I decided to make a ¼” deep recess the exact same size as my drill press table. This should keep the table from moving around from left to right. I used my CNC router to do this because my two pieces of plywood were already laminated together but you could cut the circle out with a jig saw before laminating the two pieces together.

Installing Keys

table5 (1 of 1).jpg
table4 (1 of 1).jpg

To keep the table from rotating I decided to make a couple of keys the same size as the slots in my drill press table I then could glue and screw them right to the under side of my homemade table.

Edge Banding

Screen Shot 2017-01-22 at 8.13.23 PM.png
Screen Shot 2017-01-22 at 8.13.42 PM.png

To clean up the edges, I used some ¾” maple for edge banding.

Adding T-track

Screen Shot 2017-01-22 at 8.14.12 PM.png
Screen Shot 2017-01-22 at 8.14.30 PM.png

I then could cut two dados for some T-track. This will be used for the fence as well as hold down clamps if needed. I installed the T track using screws.

Waste Insert

Screen Shot 2017-01-22 at 8.14.42 PM.png

I then cut out a 3/16” deep recess using my dado stack right in the middle of my table. The recess is 3” wide and will be use for a MDF waste insert.

Making Inserts

Screen Shot 2017-01-22 at 8.15.02 PM.png

I already had a bunch of scrap MDF so I went ahead and cut a whole bunch of inserts by ripping them 3" wide making sure they are a tight fit in the recess.

Fence

Screen Shot 2017-01-22 at 8.15.28 PM.png
Screen Shot 2017-01-22 at 8.15.42 PM.png

he fence couldn’t be easier, its just two pieces of ¾” plywood laminated together and cut to 2” wide. I then could mark the location of my T-tracks and drill corresponding holes.

Stop Block

Screen Shot 2017-01-22 at 8.16.23 PM.png
Screen Shot 2017-01-22 at 8.16.48 PM.png

You could also add some T-track on the fence front if you want, I didn’t have any left and didn’t really feel it was necessary as I could just clamp a block onto the fence for a stop.

Adding Chamfer

table2 (1 of 1).jpg
table1 (1 of 1).jpg

Finally i added a chamfer to the back so I can still rise the table without hitting my knuckles:)

Probably the best feature about this table is how easy it is to take on and off. I love how quick and easy it was to build and also how easy it is to store away when not in use.