How to Make a Desk Organizer

This Desk Organizer is capable of holding rulers, 2 calculators, protractors, papers, and tape.  This is mostly made out of PVC piping and fabric.  

Materials you will need:
    PVC pipes:
          Lengths:
              two: 8 1/2” X  ½”
              four: 3 3/4” X  ½”
              four:  1 3/4” X  ½”
              three: 3 3/4” X  ½”
              one:  5” X  ½”
              five: 1 1/2” X  ½”
              one: 1 1/2” X  ½”
          Fittings:
               T-Connector-4
               Corner-Connector-8
               90 Degree-Connector- 2  
   Wood
          Length: 4"x 10 3/4" X 1/4"  
   8 nails
   Fabric
   3D Printed attachment 

Tools you will need:
       PVC Cutter
       Tape Measurer
       Pencil
       Needle and thread 
       3D Printer
       Screwdirver
       Hot Glue Gun

1)Construct a  8 1/2” X  ½” pipe. (Either find a pipe the proper length or use a PVC Cutter to cut to the proper length)
2)Construct two 3 3/4” X  ½” pipe. (Either find a pipe the proper length or use a PVC Cutter to cut to the proper length)
3)Use a T-Connector to create a 8 1/2 pipe  
4)Construct two 1 3/4” X  ½” pipe. (Either find a pipe the proper length or use a PVC Cutter to cut to the proper length)
5)Use four corner connectors and construct a 8 1/2” by 4" rectangle 

Construct 3  7 1/2” X  ½” pipe. (Either find a pipe the proper length or use a PVC Cutter to cut to the proper length)
Put pipes in slots A,B and C

1)Construct a  5” X  ½” pipe. (Either find a pipe the proper length or use a PVC Cutter to cut to the proper length)
2)Put pipe in slot D
3)Construct a  1 1/2” X  ½” pipe. (Either find a pipe the proper length or use a PVC Cutter to cut to the proper length)
4)Use T-connector and the 1 1/2” X  ½” pipe and connect them to the left side of the T
5)Put T-connector on pipe in slot D
6)Construct a  1 1/2” X  ½” pipe. (Either find a pipe the proper length or use a PVC Cutter to cut to the proper length)
7)Put pipe in the remaining slot in the T-Connector in slot D
8)Use a 90 degree angle connector to make a hook

1)Construct a  1 1/2” X  ½” pipe. (Either find a pipe the proper length or use a PVC Cutter to cut to the proper length)
2)Use T-connector and the 1 1/2” X  ½” pipe and connect them to the left side of the T
3)Put in slot E
4)Construct a  1 1/2” X  ½” pipe. (Either find a pipe the proper length or use a PVC Cutter to cut to the proper length)
5)Put in the middle connector
6)Use a 90 degree angle and put on the 1 ½ pipe
7)Construct a  1 1/2” X  ½” pipe. (Either find a pipe the proper length or use a PVC Cutter to cut to the proper length)
8)Construct a  4 1/2” X  ½” pipe. (Either find a pipe the proper length or use a PVC Cutter to cut to the proper length)
9)Put in slot E

Construct a  8 1/2” X  ½” pipe. (Either find a pipe the proper length or use a PVC Cutter to cut to the proper length)
Construct two 3 3/4” X  ½” pipe. (Either find a pipe the proper length or use a PVC Cutter to cut to the proper length)
Use a T-Connector to create a longer pipe
Construct two 1 3/4” X  ½” pipe. (Either find a pipe the proper length or use a PVC Cutter to cut to the proper length)
Use four corner connectors and construct a 8 1/2” by 4” rectangle

1) Using a need and thread construct 2 pouches for the calculator and another for the rulers
2) Using a hot glue gun, attach pouches onto the PVC Pipe.

1) Using a hot glue gun, attach 3D printed piece on slot E.

1) Drill 4 pilot holes in the four corners 
2) Attach 4"x 10 3/4" X 1/4" to base