How to Make an Origami Heart With Wings
by Niraj.Deshmukh in Craft > Paper
3544 Views, 5 Favorites, 0 Comments
How to Make an Origami Heart With Wings
You may use any kind of paper to fold this origami heart. I am using a paper with the same red color on both sides. Make sure the paper that you use is a square (all sides are equal and all the angles equal 90 degrees). The paper I am using here is 20cm x 20cm square one. It is a good size for those who are not experienced in paper folding. If you are become familiar with this model. Then you can try smaller size paper.
Square Base
01.Let's start with "square base" . Prepare to apply two vertical valley-folds.
02.Apply two vertical valley-folds of the step #1.Prepare to unfold two valley-folds.
02.Apply two vertical valley-folds of the step #1.Prepare to unfold two valley-folds.
Inside Reverse-folds
03.Unfold previous two valley-folds.Prepare to apply two "inside reverse-folds" .
04.Apply two valley-fold of the step #3.Prepare to open the front-most layer following the arrow
04.Apply two valley-fold of the step #3.Prepare to open the front-most layer following the arrow
Inside Reverse-fold
05.Open the front-most layer.Prepare to apply an "inside reverse-fold"
06. Apply the "inside reverse-fold" of the step #5.Prepare to close it.
06. Apply the "inside reverse-fold" of the step #5.Prepare to close it.
Front-most Layer
07.Close the front-most layer.Prepare to open the front-most layer following the arrow.
08.Open the front-most layer.Prepare to apply an "inside reverse-fold" .
08.Open the front-most layer.Prepare to apply an "inside reverse-fold" .
Start for 5 Step
09.Apply the "inside reverse-fold" of the step #8.Prepare to close it.
10.Close the flap.Prepare to turn the model over.
10.Close the flap.Prepare to turn the model over.
Start for 6 Step
11.Turn the model over.Prepare to repeat the steps #1-10.
12.Repeat the steps #1-10.Prepare to apply a horizontal valley-fold.
12.Repeat the steps #1-10.Prepare to apply a horizontal valley-fold.
7
13.Apply the horizontal valley-fold of the step #12.Prepare to apply a vertical valley-fold.
14.Apply the vertical valley-fold of the step #13.Prepare to turn the model over.
14.Apply the vertical valley-fold of the step #13.Prepare to turn the model over.
8
15.Turn the model over.Prepare to apply a horizontal valley-fold.
16.Apply the horizontal valley-fold of the step #15.Prepare to apply a vertical valley-fold.
16.Apply the horizontal valley-fold of the step #15.Prepare to apply a vertical valley-fold.
9
17.Apply the vertical valley-fold of the step #16.Prepare to apply two valley-folds.These valley-folds are 45 degree angle folds and these foldings should be done just below the front-most layer.
18.Apply two valley-folds of the step #17.Prepare to apply a valley-fold and then unfold
18.Apply two valley-folds of the step #17.Prepare to apply a valley-fold and then unfold
10
19.Apply the valley-fold of the step #18 and then unfold.Prepare to apply an "open sink-fold" .
20.The crease patter of "open sink-fold" of the step #19 is shown here.
20.The crease patter of "open sink-fold" of the step #19 is shown here.
11
21.Apply the open sink-fold.Prepare to press two edges down.
22.Press two edges down.Prepare to rotate the model by 90 degrees.
22.Press two edges down.Prepare to rotate the model by 90 degrees.
12
rotate the model by 90 degrees.Prepare to apply an "inside reverse-fold" .24th picture of origami heart with wing
24.Apply the inside reverse-fold of the step #23.
24.Apply the inside reverse-fold of the step #23.
13
25.Prepare to turn the model over.
26.Turn the model over.Prepare to apply a valley-fold.
.
26.Turn the model over.Prepare to apply a valley-fold.
.
14
27.Apply the valley-fold of the step #26.Prepare to apply a mountain-fold and then unfold
28.Apply the mountain-fold of the step #27.Prepare to unfold
29.Unfold the previous fold.Prepare to apply a mountain-fold. 30th picture of origami heart with wings
30.Apply the mountain-fold of the step #29.
28.Apply the mountain-fold of the step #27.Prepare to unfold
29.Unfold the previous fold.Prepare to apply a mountain-fold. 30th picture of origami heart with wings
30.Apply the mountain-fold of the step #29.
15
31.Unfold the previous fold.Prepare to apply the CP on the left.It is called "tail-fold"
32.Apply the tail-fold of the step #31.Prepare to turn the model over.
33.Turn the model over.Prepare to apply a mountain-fold
34.Apply the mountain-fold of the step #33.Prepare to unfold.
32.Apply the tail-fold of the step #31.Prepare to turn the model over.
33.Turn the model over.Prepare to apply a mountain-fold
34.Apply the mountain-fold of the step #33.Prepare to unfold.
16
35.Unfold the previous fold.Prepare to apply a mountain-fold.
36.Apply the mountain-fold of the step #35.Prepare to unfold.
37.Unfold the previous fold.Prepare to apply another "tail-fold".
38.Apply the "tail-fold" of the step #37.Prepare to turn the model over.
36.Apply the mountain-fold of the step #35.Prepare to unfold.
37.Unfold the previous fold.Prepare to apply another "tail-fold".
38.Apply the "tail-fold" of the step #37.Prepare to turn the model over.
17
39.Turn the model over.Prepare to apply a valley-fold.
40.Apply the valley-fold of the step #39.Prepare to apply a valley-fold and then tuck it under the front-most layer.
41.Apply the valley-fold of the step #40 and then tuck it under the front-most layer.Prepare to turn the model over.
42.Turn the model over.Prepare to smooth sharp edges
40.Apply the valley-fold of the step #39.Prepare to apply a valley-fold and then tuck it under the front-most layer.
41.Apply the valley-fold of the step #40 and then tuck it under the front-most layer.Prepare to turn the model over.
42.Turn the model over.Prepare to smooth sharp edges
Done.
Smooth sharp edges..
Congratulation!
You have completed making an origami heart with wings.
Thank you .
-Niraj Deshmukh