Howl's Moving Castle Ring - Studio Ghibli

by Clayalotte in Craft > Costumes & Cosplay

3789 Views, 26 Favorites, 0 Comments

Howl's Moving Castle Ring - Studio Ghibli

20230331_195728.jpg
Screenshot_20220306-151206_DuckDuckGo.jpg
20230331_195913.jpg

In the Studio Ghibli movie, "Howl's Moving Castle" the wizard Howl gifts a magical ring to Sophie, telling her that it will provide her safety. When Howl first gives the ring to her, it has a red stone, but later while Sophie is wearing it the stone turns to blue.

Today I will be making such a ring, but I will make two: one in red and one in blue, for Howl and Sophie.

Supplies

20220409_135822.jpg
20220409_140027.jpg
20220409_140106.jpg
20220409_140217.jpg
  1. Ring Mandrel (optional, you can use another cylindrical piece that will make a ring big enough for your finger)
  2. Clay in grey (polymer clay or air dry)
  3. Two rhinestones, one red and one blue
  4. Clay roller
  5. Stylus tool (or a pencil or toothpick)
  6. Knife tool
  7. Gorilla glue or Loctite glue
  8. Silver paint
  9. Paint brush
  10. *For air dry clay: varnish

Roll Out the Ring

20220410_180316.jpg
20220410_180437.jpg
20220410_180520.jpg
20220410_180548.jpg
20220410_180646.jpg
20220410_181022.jpg
20220410_181029.jpg

First off, fetch a ring you already have. Since I am using air dry clay that will shrink slightly, I am using a ring that is just a tad too big for me. Slide it on the ring mandrel or cylindrical piece to determine where you need to wrap the clay to make the ring base.

Roll our your clay decently thin, but not too thin. With the knife tool, cut a long strip out of the clay.Wrap this piece of clay around the ring mandrel in the spot that you marked.

Smooth the ends together, trimming any excess off. Blend the ends together with a tool or your finger until they are smooth and there is no visible seam.

Adding Details and Stone Setting

20220411_103247.jpg
20220411_103404.jpg
20220411_103800.jpg
20220411_103933.jpg
20220415_165545.jpg
20220415_165558.jpg

The rings have little crosses all around them, so that is what we will add next.

Roll out the clay thinly, thinner than the ring base. We want the crosses to be slightly raised, but not huge. With the stylus tool or toothpick, draw out the shape of a cross that kind of looks like a fat clover. Cut it out with the knife tool and smooth the cut edges.

Now pick up the clover cross and place it on the ring to check the size. It should fit perfectly on the band. If the size is correct, make three more clover crosses for the ring.

Decide where the center rhinestone will go and poke a little hole there. Then space the four clover crosses equal distance apart from one another, leaving a gap where you put the center hole. The center hole is the stone setting later. Attach the clover crosses by poking a hole in the center of each cross that is deep enough to make the two clay pieces bond. (If you are using air dry clay you can use glue if you are worried about it, or if you are using polymer clay you can use liquid clay).

Painting

20220415_165830.jpg
20220419_172506.jpg

Once your clay has been baked or dried, paint the clay silver with the silver paint. I painted the entire thing, inside and out.

*TIP: If you are using polymer clay, it would be better to put silver mica powder on the unbaked clay and then bake it.

Setting the Stone

20220419_172550.jpg
20220419_172623.jpg
20230331_185455.jpg
20220419_172725.jpg
20230331_190602.jpg
20230331_190752.jpg
20230331_190917.jpg
20230331_191025.jpg
20230331_191149.jpg
20230331_191236.jpg
20230331_192309.jpg

Now we will add the stone.

Put a tiny dab of glue on the hole you made earlier. Then place the rhinestone in the hole and wait until the glue sets.

Once the glue has set, roll out a thin snake of clay to wrap around the rhinestone base. Carefully wrap around the base, cutting off the excess and smoothing the ends so there is no seam. Now take the knife tool and cut diagonal lines all around the ring setting. It should be the appearance of a twisted rope.


*TIP: If you are using polymer clay, your rhinestones have to be glass to be able to be baked in the oven. DO NOT bake plastic rhinestones!

Final Paint Coat and Varnish

20230331_193618.jpg
20230331_194045.jpg
20230331_194056.jpg

Once the setting around the stone has dried, apply the silver paint very carefully to the unpainted clay. Be very careful to not get paint on the rhinestone because cleaning that off is just an outrageous headache.

*If you are using air dry clay, you will need to varnish the piece. I recommend Duraclear Gloss varnish.

Finished

20230331_194931.jpg
20230331_195024.jpg
20230331_195237.jpg
20230331_195259.jpg

Ta-Daa! Now you have a magical ring.

I made two because I couldn't decide which color I liked more. I really love blue, but I also really wanted what Howl was wearing, which was the red. So I made both. I think that Sophie's (the blue) turned out the best.

This is a little piece of Studio Ghibli magic for me because Howl's Moving Castle is one of my absolute favorites. If you want tutorials on other pieces of jewelry from the movie, they are right here at these links: Howl's Earrings and Magic Studio Ghibli earrings.

Have a great day and Go Clay Today!