K'nex Halo Needler Guide
This is the guide for the K'nex needler.
Despite looking quite complex, the needler is very simple but is very organic in design as it uses a lot of odd angles.
I loved making this and I loved even more how awesome it looked after finishing it.
If you have any questions about the guide or the gun, just put a comment below.
Despite looking quite complex, the needler is very simple but is very organic in design as it uses a lot of odd angles.
I loved making this and I loved even more how awesome it looked after finishing it.
If you have any questions about the guide or the gun, just put a comment below.
Main Body Top Piece
This is the top half of the main body, it is a basic frame made of grey rods and many many purple connectors. The back section gets more complicated.
Main Body Bottom Piece
The bottom piece is identical to the top but the top piece has 4 extra pieces used for attaching spikes.
Structure and Support
There are a few support pieces for the main body: the handle, the forward 2 bend pieces to hold the front together and 2 pieces which have ball socket pieces and allow for the front section to be at a odd angle to the connectors of the main body but keeping it perfectly in the middle of the bottom and top body parts.
The handle is meant to be held at the top half which is larger and is held quite comfortably.
The handle is meant to be held at the top half which is larger and is held quite comfortably.
The Front
The front is quite odd.... It has 2 main parts that five the front its look but barely hold on and needs support.
The front is identical top/bottom except for the orange piece which doesn't change much.
The support pieces slide into the main parts and then go up into the main body where they attach each to 2 places.
The middle piece just sits in there attached to the 2 rods with the grey connectors.
Other than the 2 main supports the 2 front pieces need 4 pegs (white/grey rods with grey connectors) to hold the sides of the front pieces to the ends of the main body.
The front is identical top/bottom except for the orange piece which doesn't change much.
The support pieces slide into the main parts and then go up into the main body where they attach each to 2 places.
The middle piece just sits in there attached to the 2 rods with the grey connectors.
Other than the 2 main supports the 2 front pieces need 4 pegs (white/grey rods with grey connectors) to hold the sides of the front pieces to the ends of the main body.
The Details
So the details are pretty basic, attach 3 of the bendy purple rod sets on the top and bottom main body parts. then attach the 14 spikes on the top with 4 rows of 3 going back and then a row of 2 at the back. the 2 at the back are attached differently and the middle spike at the front it on a bendy piece unlike the other spikes.
What Is This Made Of???
Here it is, the list for pieces used for the needler:
green rod: 21
white rod: 73
blue rod: 22
yellow rod: 10
orange rod:10
grey rod: 10
purple bendy rod: 6
orange bendy rod: 1
grey connector: 37
light grey connector: 16
red connector: 26
green connector: 12
yellow connector: 10
white connector: 4
purple connector: 77
orange connector: 8
ball socket piece 1: 6
ball socket piece 2: 6
tan nub: 4
black nub: 21
Total pieces: 380
if you have a question about pieces take a look at my other page: https://www.instructables.com/id/Knex-Halo-Scorpion-tank-instructions/step7/What-is-it-made-of/ or ask me.
green rod: 21
white rod: 73
blue rod: 22
yellow rod: 10
orange rod:10
grey rod: 10
purple bendy rod: 6
orange bendy rod: 1
grey connector: 37
light grey connector: 16
red connector: 26
green connector: 12
yellow connector: 10
white connector: 4
purple connector: 77
orange connector: 8
ball socket piece 1: 6
ball socket piece 2: 6
tan nub: 4
black nub: 21
Total pieces: 380
if you have a question about pieces take a look at my other page: https://www.instructables.com/id/Knex-Halo-Scorpion-tank-instructions/step7/What-is-it-made-of/ or ask me.