K'nex IPod Case / Gun Instructions

by dr. richtofen in Living > LEGO & K'NEX

1006 Views, 3 Favorites, 0 Comments

K'nex IPod Case / Gun Instructions

FJD1NTSI1OTYARI.jpeg
PA230009.JPG
PA230001.JPG

Hello there,

These are the instructions to the gun / iPod case I posted a while ago.
This gun uses a medium to somewhat large amount of pieces, depending on your K'nex collection. It uses some broken rods, other broken pieces you see in the instructions aren't needed. I used them, 'cause they were lying around at the time of making this gun.

Build the Front Internals

P1190004.JPG
P1190005.JPG
P1190006.JPG
P1190007.JPG
P1190008.JPG
P1190009.JPG
P1190010.JPG
P1190011.JPG
P1190012.JPG
P1190013.JPG
P1190014.JPG
P1190015.JPG
P1190016.JPG
P1190017.JPG

These are the internals that go in the front end of the gun.

Picture 1: Most of the internals of the front
Picture 2: Parts of the exposed barrel
Picture 3: How the barrel looks on the inside
Picture 4: Build these
Picture 5: Front grip-like part
Picture 6: Build these parts
Picture 7: Attach the middle layer
Picture 8: Attach the other outer layer
Picture 9: Add these parts, but turn them around. The beige clip should be on the other end (where you can see the yellow connector in this photo)
Picture 10: Make the parts for the trigger
Picture 11: Attach them to eachother
Picture 12: Trigger part 2
Picture 13: The double ratchet
Picture 14: Another view

The Internals of the Mid-section

P1190018.JPG
P1190019.JPG
P1190020.JPG
P1190021.JPG
P1190022.JPG
P1190023.JPG
P1190024.JPG
P1190025.JPG

Picture 1: Build these
Picture 2: "attach" the other green part
Picture 3: Make this
Picture 4: The green loop is attached like this
Picture 5: Another picture
Picture 6: Attach both parts in this way.
Picture 7: Make this thing
Picture 8: Blue rod is attached in these slots

Charging Handle and Back Sights

P1190026.JPG
P1190027.JPG
P1190028.JPG
P1190029.JPG
P1190030.JPG
P1190031.JPG
P1190032.JPG
P1190033.JPG
P1190034.JPG
P1190035.JPG

Picture 1: The finished product
Picture 2: Build these parts
Picture 3: Make these
Picture 4: Clip a green rod in the ball joint connector like this
Picture 5: Make this
Picture 6: The charging handle itself
Picture 7: Attach the internals
Picture 8: Add the other outer layer
Picture 9: Grab these
Picture 10: attach them like this

Last Internals

P1190036.JPG
P1190037.JPG
P1190038.JPG
P1190039.JPG
P1190040.JPG
P1190041.JPG
P1190042.JPG
P1190043.JPG
P1190044.JPG
P1190045.JPG

Picture 1: Grab and make these
Picture 2: Attach the middle parts
Picture 3: Add other outer layer
Picture 4: Make this
Picture 5: Make this
Picture 6: Other view
Picture 7: Make these two
Picture 8: Make these
Picture 9: Those are two y clips
Picture 10: Attach like this

Outer Layer

P1190046.JPG
P1190047.JPG
P1190048.JPG

Picture 1: Front part
Picture 2: Middle part
Picture 3: Back part

Adding the Front Internals

P1190049.JPG
P1190050.JPG
P1190051.JPG
P1190052.JPG
P1190053.JPG
P1190054.JPG
P1190055.JPG
P1190056.JPG
P1190057.JPG
P1190058.JPG
P1190059.JPG
P1190060.JPG
P1190061.JPG
P1190062.JPG
P1190063.JPG
P1190064.JPG
P1190065.JPG
P1190066.JPG

Picture 1: Grab these parts
Picture 2: Add the first of those parts
Picture 3: Add the front barrel and longer row of orange connectors
Picture 4: Another view
Picture 5: Add the last part
Picture 6: Grab these
Picture 7: Attach the first part
Picture 8: Grab the front grip
Picture 9: Attach it
Picture 10: Another view
Picture 11: How it attaches in the front
Picture 12: Add this part
Picture 13: Add the last part
Picture 14: Grab the two trigger parts
Picture 15: Attach them
Picture 16: Another view
Picture 17: Grab the ratchet part
Picture 18: Attach it

Adding the Mid-section Internals

P1190067.JPG
P1190068.JPG
P1190069.JPG
P1190070.JPG
P1190071.JPG
P1190072.JPG
P1190073.JPG
P1190074.JPG
P1190075.JPG
P1190076.JPG
P1190077.JPG
P1190078.JPG
P1190079.JPG
P1190080.JPG

Picture 1: Grab this
Picture 2: Attach the hing part here
Picture 3: Attach the panel here
Picture 4: Another view
Picture 5: Another view
Picture 6: Grab this part
Picture 7: Attach it here
Picture 8: Grab the orange connector bar
Picture 9: Attach it underneath the panel, with the beige connectors facing upwards
Picture 10: Another view
Picture 11: Grab the charging handle part
Picture 12: Attach it above the panel
Picture 13: Another view
Picture 14: Another view

Adding the Back Internals

P1190081.JPG
P1190083.JPG
P1190082.JPG
P1190084.JPG
P1190085.JPG
P1190086.JPG
P1190087.JPG
P1190088.JPG
P1190089.JPG
P1190090.JPG
P1190091.JPG

Picture 1: Grab these
Picture 2: Attach here
Picture 3: Another view
Picture 4: Grab these
Picture 5: Attach here
Picture 6: Grab this
Picture 7: Attach here
Picture 8: Grab this
Picture 9: Attach here
Picture 10: Another view

The Other Outer Panel

P1190092.JPG
P1190093.JPG
P1190094.JPG
P1190095.JPG
P1190096.JPG
P1190097.JPG

Picture 1: The front
Picture 2: Mid-section
Picture 3: The back part
Picture 4: Attach
Picture 5: Attach
Picture 6: Attach

Final Bits 'n Pieces

P1190098.JPG
P1190099.JPG
P1190100.JPG
P1190101.JPG
P1190102.JPG
P1190103.JPG
P1190104.JPG
P1190105.JPG
P1190106.JPG
P1190107.JPG

Picture 1: Grab this
Picture 2: Attach it here
Picture 3: Make these
Picture 4: Add them here, with a rubberband
Picture 5: Grab a rubberband
Picture 6: Add it here
Picture 7: Grab two rubberbands
Picture 8: Trigger RB 1
Picture 9: Trigger RB 2
Picture 10: Your gun should now look like this

Loading the Gun

P1190108.JPG
P1190109.JPG
P1190112.JPG

Picture 1: Hook a rubberband on one of the two outer yellow connectors at the end of the barrel
Picture 2: Make sure it goes around the front sights on the same side
Picture 3: Hook it on the ratchet on the same side

Done!

PA230001.JPG

I hope you have fun with this gun, and be sure to tell me what you think of it in the comments!
If you have any questions about the gun, the instructions or somethi