Oblivitus' K'nex Ultra Pistol
by Oblivitus in Living > LEGO & K'NEX
7334 Views, 15 Favorites, 0 Comments
Oblivitus' K'nex Ultra Pistol
DON'T BUILD THIS, BUILD THE ULTRA PISTOL 2
Description: More powerful, accurate, stable, part efficient, and comfortable than the Super Pistol, this gun has been engineered to death as a single shot and is my most reliable k'nex weapon. The front half of the barrel is now also super light so that it still can be easily aimed and fired with one hand. This instructable was all done with MLCad. I have already made a new upgraded version of this gun with a 6 round hopper but I did make this in physical form before making the computerized version.
Influences: Loosely based on Jollex's DD-27 Pistol.
Length: 13 inches (longest section)
Width: 3 inches (widest section)
Height: 3.5 inches (tallest section)
Max Accuracy: 5 inch target from 10 feet.
Rate Of Fire: Load, cock, and fire.
Ammo: Gray rods.
Max range: 35 feet.
Features: iron sights, true trigger
Flaws: None.
Note: This gun uses 1 cut part, office tape, and duct tape.
Click here if you want to make 3D knex models:
https://www.instructables.com/id/Making-3d-knex-models-using-mlcad/
DON'T BUILD THIS, BUILD THE ULTRA PISTOL 2
Description: More powerful, accurate, stable, part efficient, and comfortable than the Super Pistol, this gun has been engineered to death as a single shot and is my most reliable k'nex weapon. The front half of the barrel is now also super light so that it still can be easily aimed and fired with one hand. This instructable was all done with MLCad. I have already made a new upgraded version of this gun with a 6 round hopper but I did make this in physical form before making the computerized version.
Influences: Loosely based on Jollex's DD-27 Pistol.
Length: 13 inches (longest section)
Width: 3 inches (widest section)
Height: 3.5 inches (tallest section)
Max Accuracy: 5 inch target from 10 feet.
Rate Of Fire: Load, cock, and fire.
Ammo: Gray rods.
Max range: 35 feet.
Features: iron sights, true trigger
Flaws: None.
Note: This gun uses 1 cut part, office tape, and duct tape.
Click here if you want to make 3D knex models:
https://www.instructables.com/id/Making-3d-knex-models-using-mlcad/
DON'T BUILD THIS, BUILD THE ULTRA PISTOL 2
Handle
1: Make this.
2: Make this. Add it on top.
3: Make this. Add it on top.
4: Make this.
5: Connect as shown.
6: This is the finished product.
2: Make this. Add it on top.
3: Make this. Add it on top.
4: Make this.
5: Connect as shown.
6: This is the finished product.
Handle/Barrel Merge
1: Make this.
2: Make this.
3: Make this.
4: Add them together.
5: Add a blue rod.
6: Make this.
7: Add it on.
8: Add a blue rod with a tan connector.
9: Add a gray connector.
10: Add the sections from step 1 and 2 together.
2: Make this.
3: Make this.
4: Add them together.
5: Add a blue rod.
6: Make this.
7: Add it on.
8: Add a blue rod with a tan connector.
9: Add a gray connector.
10: Add the sections from step 1 and 2 together.
Trigger Area
1: Make this.
2: Add green rods and a blue connector.
3: Make this. (The black pieces represent Y connectors.)
4: Add on the part from picure 3 and add 2 gray connectors to each side.
5: Add 3 blue spacers.
6: Add a ball socket connector for the back sight.
7: Make this.
8: Attach it.
9: Make this.
10: Make this. (The black piece represents a Y connector.)
11: Attach 9&10.
12: Make this.
13: Add the new pieces to it.
14: Attach it.
15: Make this.
16: Make this.
17: Add 15&16 together.
18: Put a green rod in the 45 degree connectors and cover the holes on both sides with office tape or duct tape if you don't have office tape.
19: Add a green rod to the top of the orange connector and cut it in half with scissors. (This may take several minutes if you have never done it before, it now takes me about 30 seconds because I have done it a few times.)
20: Attach trigger mech to gun.
21: Attach the 2 sections.
22: Make this.
23: Add it to the gun.
2: Add green rods and a blue connector.
3: Make this. (The black pieces represent Y connectors.)
4: Add on the part from picure 3 and add 2 gray connectors to each side.
5: Add 3 blue spacers.
6: Add a ball socket connector for the back sight.
7: Make this.
8: Attach it.
9: Make this.
10: Make this. (The black piece represents a Y connector.)
11: Attach 9&10.
12: Make this.
13: Add the new pieces to it.
14: Attach it.
15: Make this.
16: Make this.
17: Add 15&16 together.
18: Put a green rod in the 45 degree connectors and cover the holes on both sides with office tape or duct tape if you don't have office tape.
19: Add a green rod to the top of the orange connector and cut it in half with scissors. (This may take several minutes if you have never done it before, it now takes me about 30 seconds because I have done it a few times.)
20: Attach trigger mech to gun.
21: Attach the 2 sections.
22: Make this.
23: Add it to the gun.
Barrel
1: Make this.
2: Make this.
3: Attach 1&2.
4: Make this.
5: Attach 3&4.
6: Attach to the rest of the gun.
2: Make this.
3: Attach 1&2.
4: Make this.
5: Attach 3&4.
6: Attach to the rest of the gun.
Firing Rod
1: Make this. (Add duct tape the same way as on my Super Pistol.)
2: Put it on the gun and add elastics through the hole in the orange connector, stretch them to the blue rods closest to the front of the gun.
Congrats, the gun is finished.
2: Put it on the gun and add elastics through the hole in the orange connector, stretch them to the blue rods closest to the front of the gun.
Congrats, the gun is finished.
Need Help?
Message me if you are having trouble.