Steampunk Goggles
I know everyone does steampunk, but here's another one! :) It only took me about 2 hours to do this and that is with a four year old determined to help!
All you will need is:
1. fabric (I used a skirt I bought from goodwill) under $4
2. hot glue gun
3. pair of 70's disco glasses from a costume store or whatever you choose to use for the lenses. under $2 from Party City.
4. belt buckle. about $4 from joanns, but could come from anywhere...an old purse, old belt, etc.
5. doo-dads! I bought a huge bad of gears and some eyelets from Michaels for $3 each, and had some scrap-booking brads from forever ago, but also about $3.
6. scissors.
7. paper towel roll or toilet paper roll.
note: the saw in the back was for an unrelated (and actually failed) project....just ignore! :)
All you will need is:
1. fabric (I used a skirt I bought from goodwill) under $4
2. hot glue gun
3. pair of 70's disco glasses from a costume store or whatever you choose to use for the lenses. under $2 from Party City.
4. belt buckle. about $4 from joanns, but could come from anywhere...an old purse, old belt, etc.
5. doo-dads! I bought a huge bad of gears and some eyelets from Michaels for $3 each, and had some scrap-booking brads from forever ago, but also about $3.
6. scissors.
7. paper towel roll or toilet paper roll.
note: the saw in the back was for an unrelated (and actually failed) project....just ignore! :)
Destroying Glasses and Shaping Your Goggles
Step One:
You need to detach the part of the frame that hooks over your ear...sorry, I have no freaking clue what to call that part! :) I simply unscrewed mine,but it may simply depend on your glasses.
I left the center piece for stability as well as aesthetics!
Step two:
Now for the annoying part; cutting the paper towel roll to fit. It's not particularly difficult, but I am somewhat of a perfectionist and getting two the same size was a little frustrating.
My approach was to cut the first one to a general, although larger size and then slowly cut it down until it felt right. Then tracing it and cutting out the other side.
Note: they will not fit all the way around the rim of the glasses, but that's all right. I also cut a little triangle for the little lip where the screws used to be to make it fit nice and snug.
You need to detach the part of the frame that hooks over your ear...sorry, I have no freaking clue what to call that part! :) I simply unscrewed mine,but it may simply depend on your glasses.
I left the center piece for stability as well as aesthetics!
Step two:
Now for the annoying part; cutting the paper towel roll to fit. It's not particularly difficult, but I am somewhat of a perfectionist and getting two the same size was a little frustrating.
My approach was to cut the first one to a general, although larger size and then slowly cut it down until it felt right. Then tracing it and cutting out the other side.
Note: they will not fit all the way around the rim of the glasses, but that's all right. I also cut a little triangle for the little lip where the screws used to be to make it fit nice and snug.
Cutting the Fabric
Step 3: The inside of the goggles
I basically did the same thing as I did making the second cut-out of the paper towel roll. I "traced" it, leaving a centimeter of spare cloth around the edge that is closest to the lens AND leaving a strip that would wrap around the rest of the goggles that did not have the paper towel "frame". I started by gluing down the center first and making sure it was smooth. The cloth I chose was pretty stretchy-to use the technical term- so when it came time to glue down the sides, I glued a little down at a time and kept it taught until it dried (so for about 1.5 seconds). This way there was no bunching around the edges and no need to cut slits, as I would have had the cloth been less pliable.
Step 4: The outside of the goggles
For this part, I specifically chose to align the pre-made seems of the skirt so that they were visible and traced yet again leaving a centimeter of extra around every side except the part closest to the lens. I should also mention that I wanted to use the bottom of the skirt to the the seem around the goggles was slightly worn, but still neater than it would have it I had sewn it or glued it down.
Again, I started by gluing down the center first and keeping the edges taught until dry.
For the trickier center part I simply trimmed it to size and put a very small dab of glue on the tip and molded the cloth around the nose-bar-thing of the glasses. I figured there was nothing that needed to be supported there and I just needed it to stay in place.
Note: This process does not make for a very pretty inside portion of the goggles, but since mine (and most everyone else's) were to be sitting on my head, I didn't care. It doesn't actually look as bad as the picture shows, but I did want to make a point of showing it.
I basically did the same thing as I did making the second cut-out of the paper towel roll. I "traced" it, leaving a centimeter of spare cloth around the edge that is closest to the lens AND leaving a strip that would wrap around the rest of the goggles that did not have the paper towel "frame". I started by gluing down the center first and making sure it was smooth. The cloth I chose was pretty stretchy-to use the technical term- so when it came time to glue down the sides, I glued a little down at a time and kept it taught until it dried (so for about 1.5 seconds). This way there was no bunching around the edges and no need to cut slits, as I would have had the cloth been less pliable.
Step 4: The outside of the goggles
For this part, I specifically chose to align the pre-made seems of the skirt so that they were visible and traced yet again leaving a centimeter of extra around every side except the part closest to the lens. I should also mention that I wanted to use the bottom of the skirt to the the seem around the goggles was slightly worn, but still neater than it would have it I had sewn it or glued it down.
Again, I started by gluing down the center first and keeping the edges taught until dry.
For the trickier center part I simply trimmed it to size and put a very small dab of glue on the tip and molded the cloth around the nose-bar-thing of the glasses. I figured there was nothing that needed to be supported there and I just needed it to stay in place.
Note: This process does not make for a very pretty inside portion of the goggles, but since mine (and most everyone else's) were to be sitting on my head, I didn't care. It doesn't actually look as bad as the picture shows, but I did want to make a point of showing it.
Now for the Fun Part!
Step 5: The strap
My sewing machine is caput at the present so for the strap I cut a piece the length I needed and double wide. I folded it over and glued it down and that was that! One end was glued to the inside of the goggles and the other I punched a hole through and added an eyelet for the belt buckle.
Step 6: personalize! I have done a lot more to this pair since I took the pictures,but you get the jist of it!!
My sewing machine is caput at the present so for the strap I cut a piece the length I needed and double wide. I folded it over and glued it down and that was that! One end was glued to the inside of the goggles and the other I punched a hole through and added an eyelet for the belt buckle.
Step 6: personalize! I have done a lot more to this pair since I took the pictures,but you get the jist of it!!