The Ultamate Halo 3 Instructable

welcome to The Ultamate Halo 3 Instructable its DIY and Stuff and i have 5 project from the very famous XBOX 360 hit HALO 3 

The Halo 3 Battle rifle (next step)

The SMG (at 5)

The Magnum (at 9)

The energy sword (at 14)

I hope you like ths and dont forget to vote for me

Lets start things of with a headshot with the trusty halo 3 battle rifle

what you will need is

Materials:

pvc any width
pvc joints to fit the pvc
a lot of electrical tape
a sprite zero bottle
the cap to the sprite zero bottle
a screw
packageing tape 
and cardboad

Tools:

a hacksaw
a drill
a clamp
scissers
and a razor blade

now get your pvc and cut it into 13 pices
x1 1inch
x1 11/2 inch
x1 2 inch
x4 4 inch
x3 5 inch
x2 7 1/2 inch
x2 9 inch
and use your
x7 90 elbos
x1 t brackets
x1 conector
x2 45 elbos
and conect the pvc shown

now its time for the scope first you  take onr of your 4 inches and your 1 inche and a t elbo and conect them to the long pieces (twss)
 and now take your sprite zero bottle and cut the top off and figure it as much as you like until its perfect for you but before we put it togther you might want to use a grinder to get a better fit on the pvc but you dont have to but all you have to do is drill a hole into the middle of the cap t elbo and the top of the gun shown 

now you need to get card board and cut in the shpe of a gun handle and tape it to the bottom so its confterbale like shown and cover it all in electrcal tape then, use cardboard to make the rail in the front top of the gun
cover that and then tape it on, now use some excess pvc and tape it on the bottom of the barrle and you done

now if you do this project please leave your pics below in a comment i want to see how you guys did as well and i wilkl try to bu up every week with answers on comments and every 2 weeks with an instructable now on to the smg

(Ps. to see the final product by itself go th the second to last page) 

One of the fastest and one of my favorite guns The SMG

materials:

cardboard
pens
electrical tape
and cutting utensiles

 

first you draw out your smg and cut it out twice, theres really not much to say about it

now what i did is i took 3 more pieces of cardboard and cut them so they give the gun demention but if you like hard work you can just cut out 3 more layers(3 layers to fit the pvc it varrys from different thickness of pvc) so layer it out like shown

for less trouble you might want to tape the pieces to the outer layer then tape the other layer on top

now you just cover it all in electrical tape

for the barrle i really culdent find a way to put it on the gun so i just taped it on

now you are done

dont forget to post you work in the comments
 
now lets shoot em up with the magnum

The Halo Magnum sucked in Halo 3 but is a boss in ODST

materials:

cardboard
gray duct tape
piece of plastic
and more cutting utencils

first i needed to get a feel for the shape so i got a pic offline but you dont need one
 

now cut two pieces without the magazine and those will be your outer pieces

now cut 2 more still no magasine but the front of the gun shorter like shown

now cut a rectangle in the handle on both smaller guns and tape them together

now you take the two inner pieces and the outer pieces and tape them up ande cover all ofit in duct tape until the tip then for the tip you put the small piece of plastic at the top area of the gun for the barrle

now add the magazine in the bottom of the gun and your done

dont forget to ad your pics in the comments

now for the ****** *****

this w as one of my many mistakes so just skp this step

Its the energy sword and this is the final project it is the shortest project so what you need is

More crdboard
more cutting utencils for the cardboard
x2 90 elbo
x1 t elbo
metalc, electrical, and regualr scoch tape
and two short pices of pvc

tools a drill and a hack saw

first you use a sharpie to draw the sword around the pvc and make sure its 2 layers thick but dont attach the pvc yet then cover the blades in metalic tape

now draw lines on the 90 elbos like show drill a hole in the part show and saw out the rest on both pieces 

now you isert the pvc into the elbos and tape up the pvc to make it stay and then insert the cardboard and sucure it and you are done

now you can just hold them and say i got a halo 3 prop or make videos speaking of videos i am working on 3 trailors for mini movies and i want you the veiwers to pick the video in might be in a couple weeks but the video will be picked by you guys thanks for veiwing and dont forget to vote for me in the game life challenge