Waterfall Planter Designed in Tinkercad

by Coleman13 in Workshop > 3D Printing

1874 Views, 28 Favorites, 0 Comments

Waterfall Planter Designed in Tinkercad

Screen Shot 2020-04-26 at 11.00.50 PM.png
Screen Shot 2020-04-17 at 9.27.55 PM.png
IMG_20200426_181119.jpg

Designed a waterfall planter for succulents and other small plants in Tinkercad. Then i 3D printed it and made many adjustments on the way.

Supplies

The following are the parts i used:

glue gun

glue sticks

wire strippers

3D design tool

- TinkerCad

3D printer slicer

- PrusaSlicer

12V AC to DC adapter w/ power terminals

- You only need one that is 2 Amps

12V motor controller

12V Submersible water pump

3D printer:

- i use the Prusa MK3S

PLA Filament:

-I used Hatchbox Black PLA

Plastic Tubing

Your plants of choice

- Succulents and Scotch Moss

Assorted Rocks

- 5 dollars for huge bag really only needed a handful

Design Process Creating the Base

Screen Shot 2020-04-07 at 8.29.50 PM.png
Screen Shot 2020-04-07 at 9.15.56 PM.png

Used terrain as the base for the model.

Then added brick walls to create a stone container for the electronics. i put 4 walls together and then stacked another 4 on top of those to add height.

Create Archways and Side Walls

Screen Shot 2020-04-07 at 9.06.19 PM.png
Screen Shot 2020-04-07 at 9.17.43 PM.png
Screen Shot 2020-04-07 at 9.14.37 PM.png
Screen Shot 2020-04-07 at 8.58.52 PM.png
Screen Shot 2020-04-07 at 9.02.30 PM.png
Screen Shot 2020-04-07 at 9.07.28 PM.png
Screen Shot 2020-04-07 at 9.08.51 PM.png
Screen Shot 2020-04-07 at 9.27.06 PM.png

I used round roof as a hole to create archways on both sides of the model.

Then I created more brick walls. This time choosing the one with square bricks. I used boxes as holes to cut of extending ends of the walls and cut down the height. Then I copy and pasted these walls and rotated them to create a perimeter all the way around.

Making the Brick Walls Solid

Screen Shot 2020-04-07 at 10.12.49 PM.png
Screen Shot 2020-04-07 at 10.17.08 PM.png

To make the brick walls solid Ii added a thin box between all the walls on the main structure and the perimeter to make it more water tight.

Creating the Waterfall

Screen Shot 2020-04-07 at 9.32.31 PM.png
Screen Shot 2020-04-10 at 4.30.20 PM.png

I used the roof shape and stretched it out create the waterfall. Then I cut off the extra back with a box hole.

I then used a box hole that I shrunk and pressed in to create ridges on either side of the waterfall to make sure the water wouldn't splash of the sides.

Create Holes for Electronics and a Box for the Water Pump

Screen Shot 2020-04-10 at 4.45.11 PM.png
Screen Shot 2020-04-10 at 4.50.48 PM.png
Screen Shot 2020-04-10 at 4.58.39 PM.png
Screen Shot 2020-04-26 at 9.21.14 PM.png
Screen Shot 2020-04-17 at 8.54.10 PM.png
Screen Shot 2020-04-17 at 9.14.01 PM.png

I used my digital calibers to measure all my electronics to create them and then turn them into holes.

I also modeled the water pump and created a box for it to sit in.

- The first version of this box failed to hold enough water so i decided to extend it.

Creating Stilts for the New Water Bucket

Screen Shot 2020-04-17 at 9.01.06 PM.png
Screen Shot 2020-04-17 at 9.08.25 PM.png
Screen Shot 2020-04-17 at 9.19.28 PM.png

Now that the water bucket is under the waterfall I needed something to hold up the planter.

I used the brick walls to create brick columns. Then used boxes at the top and bottom to make it flush.

After I created the stilts, I used a box to cut a hole to allow water into the bucket. Also, a cylinder to create a hole on the front of the waterfall.

Creating the Side Planters

Screen Shot 2020-04-07 at 9.51.41 PM.png
Screen Shot 2020-04-07 at 9.57.06 PM.png
Screen Shot 2020-04-07 at 9.57.13 PM.png
Screen Shot 2020-04-26 at 9.30.19 PM.png
Screen Shot 2020-04-26 at 9.30.29 PM.png
Screen Shot 2020-04-07 at 9.57.29 PM.png
Screen Shot 2020-04-07 at 9.54.05 PM.png
Screen Shot 2020-04-07 at 11.15.20 PM.png

I used a diamond as the base, cutting it so it was only the flat half. Then rotated it on its head.

Next I put a round roof that was rotated to be the top.

Then used a half sphere as a hole that i stretched through until it slightly poked through. This had the added benefit of creating a drainage hole.

Lastly I used the box hole to slice of about a 1/4 of the planter and positioned 4 of them on the model

Creating the Top Planter

Screen Shot 2020-04-26 at 9.38.23 PM.png
Screen Shot 2020-04-26 at 9.35.53 PM.png
Screen Shot 2020-04-26 at 9.36.19 PM.png

Started with two rectangles on top of each other.

Then added a box hole through the two to give room for the planter.

I adjusted these to fit into the dimensions of the top of the waterfall planter.

Then used 3 cylinders to create drainage holes.

Downloads

Space and Covering for the Tubing

Screen Shot 2020-04-10 at 5.07.39 PM.png
Screen Shot 2020-04-26 at 9.42.14 PM.png
Screen Shot 2020-04-10 at 5.41.12 PM.png
Screen Shot 2020-04-26 at 9.42.43 PM.png
Screen Shot 2020-04-26 at 9.42.03 PM.png

Used a cylinder hole to create a hole through the top of the waterfall.

I used two cylinders and a box to create a covering. This helps direct water flow to the bottom instead of shooting straight out of the hole.

Electronics Cover

Screen Shot 2020-04-26 at 9.41.45 PM.png

i created a small electronics cover out of two boxes to protect them from drippings of back splash.

Print the Model and All Its Parts.

Screen Shot 2020-04-10 at 5.45.22 PM.png

Print the Model marked V2 along with the parts mentioned in steps 6, 8, and 10. The one with stilts has the model with all the parts attached besides the top and would be hard to print as is.

Suggestions when slicing:

Use .2mm layer height.

Use support enforcers to create blocks under the planters on the side. If you use supports on the whole thing it will waist a ton of plastic. If you do not know how to do this you can print with supports on the whole model.

Use a brim on the main print. It is large and could lift off the bed.

If you can use 100% infill on the water bucket to make it hold water better.

Wire Electronics

Screen Shot 2020-04-26 at 10.14.45 PM.png

Wire your electronics as seen in the diagram. When the potentiometer (knob) on the motor controller is turned all the way to the left it will act as an off switch so no need to add a power switch.

Put Tube Into Water Fall

IMG_4154.jpg
IMG_4155.jpg
IMG_4156.jpg

Attach the tube to the water pump and feed it through hole in the back.

See how long you need it to be with a little extra slack and cut it.

Stick it through the hole at the top of the water fall. It should be snug and then use a little hot glue to seal it in place if you can.

Place Electronics

Put the electronics in their appropriate holes and seal their open terminals with hot glue. Use the electronics cover from step 10 to cover the top and then glue that in place to create a seal around it.

Mesh Cover for Drainage Hole

IMG_20200426_165803.jpg
IMG_20200426_170015.jpg
IMG_20200426_172349.jpg

I found a model on Thingiverse for a mesh covering for a computer fan.

I printed that and cut it down to size.

Then hot glued it over the hole. This stops soil and rocks from getting in the water bucket.

Attach Water Bucket and Stilts If Printed Separately

IMG_20200426_171632.jpg

Use hot glue to attach the legs.

Use the hot glue around the entire perimeter of the water bucket to create a seal.

You can cut the excess glue off with a crafting knife after.

Glue on the Rocks

IMG_20200426_173227.jpg
IMG_20200426_173958.jpg
IMG_20200426_173128.jpg
IMG_20200426_180200.jpg

Test out the orientation of the rocks you want to use. Then use hot glue and one at a time press them on.

- I suggest using a few larger rocks at the base to create a higher wall to block water overflow.

- My updated model has a higher front wall to fix that issue.

Add on Your Plants

IMG_20200426_181230.jpg
Waterfall Planter designed in Tinkercad
IMG_20200426_181209.jpg

Place your plants in each appropriate planter. Then plug it in and enjoy your relaxing waterfall planter.

Feel free to give any suggestions or design ideas. Thank you!