How to Make a Flash Suppresor/silencer for an Airsoft Gun
by el_ak-47 in Outside > Launchers
10581 Views, 8 Favorites, 0 Comments
How to Make a Flash Suppresor/silencer for an Airsoft Gun
make a flash suppresor/silencer for our airsoft gun using the venturis from a gas grill burner assembly!!
it gives the opposite team a scare when you first pull your gun
out! why waste time on ebay searching for cool silencers when you can use your old not so handy dandy venturis!!
this is my first instructable,so HIT ME WITH YOUR BEST SHOT!!
if you have a bad comment regarding the instructable, BRING IT!!
if its good, much apprediated.
*NOTICE FINE PRINT* if you comment me, i will comment one of your instructables in the same fashion as you did mine.
BAD COMMENT= BAD COMMENT FOR YOU, UNLESS ITS CONSTRUCTIVEE.
GOOD COMMENT=GOOD COMMENT FOR YOU, PROPS
it gives the opposite team a scare when you first pull your gun
out! why waste time on ebay searching for cool silencers when you can use your old not so handy dandy venturis!!
this is my first instructable,so HIT ME WITH YOUR BEST SHOT!!
if you have a bad comment regarding the instructable, BRING IT!!
if its good, much apprediated.
*NOTICE FINE PRINT* if you comment me, i will comment one of your instructables in the same fashion as you did mine.
BAD COMMENT= BAD COMMENT FOR YOU, UNLESS ITS CONSTRUCTIVEE.
GOOD COMMENT=GOOD COMMENT FOR YOU, PROPS
Gather the Materials!!
materials:
1-hacksaw
2-pen, pencil, something to fit inside barrel
3-Venturis( i think that's what its called)
4-electrical tape
5-the most important piece, the gun
my dad sat on my gun while it was on my bed and broke the barrel
so, this proves that nessecity is the mother of all creations
(Mother nessecity, where would we be? plays in background)
1-hacksaw
2-pen, pencil, something to fit inside barrel
3-Venturis( i think that's what its called)
4-electrical tape
5-the most important piece, the gun
my dad sat on my gun while it was on my bed and broke the barrel
so, this proves that nessecity is the mother of all creations
(Mother nessecity, where would we be? plays in background)
Grab the Venturis
alright, grab the venturis and look for an ideal spot to cut it seperate from the bend
on mine, its about on the edg of the wood thing
on mine, its about on the edg of the wood thing
Hack Away, Hackers!!
grab your deadly hacksaw and hack away at the spot you've chosen!
it help if you do what i did and put it on the edge of something and put your fott on it
it help if you do what i did and put it on the edge of something and put your fott on it
Clean It!
grab the now shorter venturis and the pencil and/or item of your choice and slide the pencil in the venturis.
now start to scrape the inside with in/out/circle motions
(freakin perverts, might as well stick the pencil in your head to clean it out. :p lol, j/k)
this step is to remove the rust or debris inside
now start to scrape the inside with in/out/circle motions
(freakin perverts, might as well stick the pencil in your head to clean it out. :p lol, j/k)
this step is to remove the rust or debris inside
Fit It!
now, stick the now semi- clean venturis on the gun barrel.
if its bigger than the guns barrel read on.
if its just the right size, finito!, your finished.
if its bigger, you will need a male/female hose connector.
the male part of the hose connector should be small enough to hug the barrel.
the second picture shows the male/female connector.
i'll go over this step next
if its bigger than the guns barrel read on.
if its just the right size, finito!, your finished.
if its bigger, you will need a male/female hose connector.
the male part of the hose connector should be small enough to hug the barrel.
the second picture shows the male/female connector.
i'll go over this step next
Adjust It Firmly!!
if it didn't fit, you need a male/female hose connector as show in the previous picture.
apply electrical tape GRADUALLY to the venturis, this means
put a little on then check if it fits snugly in the female part(of the connector, pervs)
then slide the male part into the barrel of the gun, put some tape on the male to ensure a snug fit
apply electrical tape GRADUALLY to the venturis, this means
put a little on then check if it fits snugly in the female part(of the connector, pervs)
then slide the male part into the barrel of the gun, put some tape on the male to ensure a snug fit
Slide It In!
there you have it!!
just slide it in or off
try using sand paper to give the suppresor a war-torn look.
and try spray painting the hose connector, mine's pink, but im gonna spray it.
gratzi. im not italian, im hispanic, but i like other languages.
and guns
just slide it in or off
try using sand paper to give the suppresor a war-torn look.
and try spray painting the hose connector, mine's pink, but im gonna spray it.
gratzi. im not italian, im hispanic, but i like other languages.
and guns